eFunda Properties of Alloy Steel Alloy Steel AISI 4340

Tensile Strength (MPa) 744.6 Yield Strength (MPa) 472.3 Elongation (%) 22.0 Reduction in Area (%) 49.9 25 normalized at 870°C Tensile Strength (MPa) 1279.0 Yield Strength (MPa) 861.8 Elongation (%) 12.2 Reduction in Area (%) 36.3 25 oil quenched, fine grained, tempered at 205°C Tensile Strength (MPa) 1875 Yield sae 4340 tensile strength

Contact Supplier

Datasheet 4340 ALLOY STEEL AMS 6414 VAR

4340 ALLOY STEEL AMS 6414 VAR UNSG43406 DATA SHEET GENERAL CHARACTERISTICS 4340 VAR AMS 6414 is a low alloy Chromium-Nickel-Molybdenum steel capable of being heat treated to high strength levels. This specification is for a premium aircraft-quality, low-alloy steel in the form of bars, forgings, mechanical tubing, and forging stock.

File Size 218KB

Contact Supplier

SAE-AISI 4340 (SNCM439, G43400) Ni-Cr-Mo Steel sae 4340 tensile strength

G43400 is the UNS number. It can have a moderately high tensile strength among SAE-AISI wrought steels. In addition, it has a moderately high base cost and a moderately high electrical conductivity. The properties of SAE-AISI 4340 steel include four common variations.

Contact Supplier

4340 High Tensile Steel Interlloy Engineering Steels sae 4340 tensile strength

4340 is a 1.8% nickel - chromium - molybdenum high hardenability high tensile steel - generally supplied hardened and tempered in the tensile range of 930 - 1080 Mpa (condition U) - (Rc 28 - 36).. Characterised by high strength and toughness in relatively large sections. Pre hardened and tempered 4340 can be further surface hardened by flame or induction hardening and by nitriding.

Contact Supplier

4340 Hardened and Tempered Bar - Interlloy

4340 is a 1.8% nickel - chromium - molybdenum high hardenability high tensile steel - generally supplied hardened and tempered in the tensile range of 930 - 1080 Mpa (condition U) - (Rc 28 - 36).. Characterised by high strength and toughness in relatively large sections.

Contact Supplier

Normalized SAE-AISI 4340 vs. SAE-AISI 4340M Steel sae 4340 tensile strength

May 30, 2020 · Both normalized SAE-AISI 4340 and SAE-AISI 4340M steel are iron alloys. They have a very high 98% of their average alloy composition in common. There are 31 material properties with values for both materials. Properties with values for just one material (4, in this case) are not shown.

Contact Supplier

AISI 4340 Alloy Steel (UNS G43400) - AZoM

Topics Covered

Contact Supplier

4340 Steel 36CrNiMo4 1.6511 EN24 SNCM439 - Otai sae 4340 tensile strength

AISI 4340 steel is a medium carbon, low alloy steel known for its toughness and strength in relatively large sections. AISI 4340 is also one kind of nickel chromium molybdenum steels. 4340 alloy steel is generally supplied hardened and tempered in the tensile range of 930 - 1080 Mpa. Pre hardened and tempered 4340 steels

Contact Supplier

4130, 4340, AMS 6345, AMS 6348,AMS 6414, AMS 6415,

AISI 4340 is a heat treatable, low alloy steel containing nickel, chromium and molybdenum. Alloy 4340 is known for its toughness and capability of developing high strength in the heat treated condition while retaining good fatigue strength. Typical applications for 4340 alloy steel are for structural use, such as aircraft landing gear, power sae 4340 tensile strength

Contact Supplier

eFunda Properties of Alloy Steel Alloy Steel AISI 4340

Tensile Strength (MPa) 744.6 Yield Strength (MPa) 472.3 Elongation (%) 22.0 Reduction in Area (%) 49.9 25 normalized at 870°C Tensile Strength (MPa) 1279.0 Yield Strength (MPa) 861.8 Elongation (%) 12.2 Reduction in Area (%) 36.3 25 oil quenched, fine grained, tempered at 205°C Tensile Strength (MPa) 1875 Yield sae 4340 tensile strength

Contact Supplier

AMS4340G Aluminum Alloy, Extrusions 6.2Zn - SAE International

Aluminum alloys Coatings, colorants, and finishes Magnesium alloys Extrusion Conductivity Tensile strength Heat treatment Welding. Also known as SAE AMS 4340 SAE MOBILUS. Subscribers can view annotate, and download all of SAE's content.

Contact Supplier

AISI 4340 Alloy Steel (UNS G43400) - AZoM

AISI 4340 alloy steel is annealed at 844°C (1550°F) followed by cooling the furnace. Tempering. AISI 4340 alloy steel should be in the heat treated or normalized and heat treated condition before tempering. Tempering temperatures depend upon the desired strength level. Hardening. AISI 4340 alloy steel can be hardened by cold working or heat sae 4340 tensile strength

Contact Supplier

AISI 4340 1.6511 36CrNiMo4 SNCM439 - Xingsheng sae 4340 tensile strength

AISI 4340 is defined as a heat treatable and low alloy steel which has 0.8% Cr, 0.2% Mo and 1.8% Ni as strengthening alloy elements.Compared with AISI 4140,it has higher strength and toughness,also it has very good fatigue resistance, wear resistance and atmospheric corrosion resistance.AISI 4340 is generally supplied in hardened and tempered condition with the tensile range of 930 - 1080 Mpa sae 4340 tensile strength

Contact Supplier

Encore Metals - 4340

AISI 4340 is stocked in the heat treated and stress-relieved condition at approximately 150,000 psi (1034 N/mm2) and in the annealed condition at HB 235 max. Typical Applications High strength machine parts, heavy-duty shafting, high tensile bolts and studs, gears, axle shafts, crankshafts, boring bars and down-hole drilling components

Contact Supplier

Solved The Figure Shows An S-N Curve For AISI 4340 Steel sae 4340 tensile strength

The figure shows an S-N curve for AISI 4340 steel, hardened to a tensile strength of 1800 MPa. What is the endurance limit? If cycled for 100 cycles at an amplitude of 1200 MPa and a zero mean stress, will it fail? If cycled for 100,000 cycles at an amplitude of 900 MPa and zero mean stress, will it fail?

Contact Supplier

ASM Material Data Sheet

Tensile Strength, Yield 710 MPa 103000 psi Elongation at Break 13.2 % 13.2 % Reduction of Area 36 % 36 % Modulus of Elasticity 205 GPa 29700 ksi Typical for steel Bulk Modulus 140 GPa 20300 ksi Typical for steel. Poisson's Ratio 0.29 0.29 Calculated Machinability 50 % 50 % annealed and cold drawn. Based on 100% sae 4340 tensile strength

Contact Supplier

4130, 4340, AMS 6345, AMS 6348,AMS 6414, AMS 6415,

AISI 4340 is a heat treatable, low alloy steel containing nickel, chromium and molybdenum. Alloy 4340 is known for its toughness and capability of developing high strength in the heat treated condition while retaining good fatigue strength. Typical applications for 4340 alloy steel are for structural use, such as aircraft landing gear, power sae 4340 tensile strength

Contact Supplier

Tensile / Yield Strength of Steel Chart

Yield Strength, Tensile Strength and Ductility Values for Steels at Room Temperature Material Yield Strength Tensile Strength % Elong. MPa (ksi) MPa (ksi) sae 4340 tensile strength Steel Alloy 4340 - Annealed (@810 °C) 472 (68.5) 745 (108) 22 Steel Alloy 4340 - Normalized (@870 °C) 862 (125) 1280 (185.5) 12.2 Steel Alloy 4340 - Oil-quenched and tempered (@315 sae 4340 tensile strength

Contact Supplier

4340 Steel 36CrNiMo4 1.6511 EN24 SNCM439 - Otai sae 4340 tensile strength

AISI 4340 steel is a medium carbon, low alloy steel known for its toughness and strength in relatively large sections. AISI 4340 is also one kind of nickel chromium molybdenum steels. 4340 alloy steel is generally supplied hardened and tempered in the tensile range of 930 - 1080 Mpa. Pre hardened and tempered 4340 steels

Contact Supplier

4340 ALLOY STEEL AMS 6414 VAR UNSG43406

4340 VAR AMS 6414 is a low alloy Chromium-Nickel-Molybdenum steel capable of being heat treated to high strength levels. This specification is for a premium aircraft-quality, low-alloy steel in the form of bars, forgings, mechanical tubing, and forging stock.

Contact Supplier

AISI Carbon Steel Mechanical Characteristics Table Chart sae 4340 tensile strength

AISI Carbon Steel Mechanical Characteristics Table Chart Yield, Tensile, Hardness AISI 3140 - AISI 9310 . Metal Products Distributor Supplier Metals and Materials Table of Contents. sae 4340 tensile strength Strength . Elongation, (%) Hardness, Bhn . Tensile . Yield . psi (lb/in. 2) 3140. Normalized (1600 F)

Contact Supplier

Aircraft Alloy Steel AISI 4340 / E-4340 - Aircraft Materials

Alloy E 4340 is a widely used deep-hardening constructional steel. Due to E-4340's high alloy content it obtains a uniformed hardness by heat treatment. The high fatigue strength makes E4340 ideal for highly stress parts as it maintains it's strength and hardness at elevated temperatures.

Contact Supplier

(PDF) General relation between tensile strength and sae 4340 tensile strength

Fitting relation between tensile strength and rotating bending fatigue ratio of high strength steels (a) SAE 4140; (b) SAE 4340; (c) SAE 2340 and (d) SAE 4063. (Data are cited from Ref. [38] ).

Contact Supplier